• Introducing what has been requested for too long already A super-efficient iFlight 7inch Long-Range bird that can go where you couldn&x27;t go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want A super stiff frame for minimum resonance and XING2 2809 motors for maximum 7inch prop control. Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising. But whatever style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S 2.500mAh above.
  

• GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behavior; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts are included to cover you and your antenna dead-ends just in case. GoPro universal TPU bottom stand included; fits your original GoPro bracket and our TPU GoPro protectors (additional).
  

Main Changelog from Chimera7 to Chimera7 Pro:

• SucceX-D F7 V2.2 Stack (F7+50A ESC) upgraded to BLITZ F722 Stack (F7 V1.1 + 55A 4in1 ESC)

• New Lightweight Side Panels Design - Keep Your Rig Clean
  

• XING 2806.5 upgraded to XING2 2809 1250KV

• 7-inch frame upgraded to 7.5inch
  

HIGHLIGHTS:

• Battery voltage LED status light (illuminated IF logo on the bottom)

• GoPro TPU bottom stand (GoPro protector not included)
• Lightweight Side Panels Design - Keep Your Rig Clean
• XING2 2809 1250KV efficient wide stator motors

• GPS pre-installed for more safety at a distance
  

• 360° TPU protection, FPV cam protection

• 6mm rigid arm design for more stiffness

• Top- and bottom battery mount option
  

PRE-TUNED & PRE-SETUP:

• Is this your first BNF or are you just starting through with FPV? This article might probably help: General Guide // iFlight BNF
  

• Don&x27;t worry about tuning, we did that for you already A basic PID- and Filter tuning was applied for a great flight experience

• To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"

• Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn&x27;t end in a mess

• Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"

• GPS Rescue is OFF by default to prevent unwanted or unexpected drone behavior.

• Please check our linked article on"GPS Rescue Mode // Setup"
  

Specifications:

• Weight: 695g (without battery and GoPro mount)
  

• Total Dimensions: 258*200mm (body dimension)

• Upper(middle) Plate Thickness: 3mm

• Bottom to Top Distance: 20-29mm

• Bottom Plate Thickness: 3mm

• Camera Plate Thickness: 3mm

• Top Plate Thickness: 3mm
  

• Geometry: DC (DeadCat)

• HQ 7.5X3.7X3 Propellers
  

• Arm Thickness: 6mm

• XING2 2809 1250KV

• FC: BLITZ F722

• ESC: BLITZ E55 4-IN-1 2-6S ESC
  

ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC)：

FC // BLITZ F722 Flight Controller

• Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter

• Smartaudio / IRC Tramp VTX protocol supported

• Firmware target: IFLIGHT_BLITZ_F722

• Motor outputs: 4x (SH1.0 connector)

• Flash: 32MB (Blackbox flash)

• I2C serial: SDA / SLA pads

• Dimensions: 36.5*35 mm

• Barometer: DPS310

• OSD Chip: AT7456E

• LED controller: Yes

• MCU: STM32 F722

• Beeper pad: Yes

• Gyro: BMI270

• Weight: 7.8g

• UARTS: 6
  

ESC // BLITZ E55 4-IN-1 2-6S 55A ESC

• Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
  

• Mounting Holes: 30.5*30.5mm/Φ4mm
  

• Target: IFLIGHT_BLITZ_G2
  

• Supports 2-6S Lipo input
  

• Current sensor: Yes
  

• Constant: 55 Amps
  

• Current rate: 200
  

• Burst: 65 Amps
  

• Weight: 15.3g
  

• MCU： G071
  

• BEC: No
  

Tips:

• VTX is set to 25mW by default Power levels above 25mW require a HAM license or have to be approved by local authorities Please ensure you&x27;re flying legal frequencies and use our prepared Betaflight VTX tables according to your region.